RomRaider Logo

RomRaider

Open Source ECU Tools
 FAQ •  Register •  Login 

RomRaider

Documentation

Community

Developers

It is currently Fri Jan 19, 2018 9:07 am

All times are UTC - 5 hours [ DST ]





Post new topic Reply to topic  [ 69 posts ]  Go to page Previous  1, 2, 3, 4, 5
Author Message
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Tue Jan 26, 2010 4:35 pm 
Offline
Senior Member

Joined: Mon Jan 19, 2009 2:31 pm
Posts: 1384
Location: Saratov, Russia
I am completely sure there are unused ecu pins available (ReadMemory, SubWriteProtection, etc.) that may be used to force 32bit ecu to change baudrate by means of an appropriate ecu hack.

RomRaider logger may be routinely reconfiged for another baudrate here (logger.xml):
<protocol id="SSM" baud="4800" databits="8" stopbits="1" parity="0" connect_timeout="2000" send_timeout="55">

I tried this successfully for 19200, 38400bps and MicroChip 16 bit dsPIC based ecu.


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Tue Jan 26, 2010 4:48 pm 
Offline
Experienced

Joined: Sat May 31, 2008 10:14 pm
Posts: 125
Location: Quebec
You mean you successfully communicate with a 16 bits ecu at 19200 and 38400 just by changing the baud rate at the init?

Sasha_A80 wrote:
I am completely sure there are unused ecu pins available (ReadMemory, SubWriteProtection, etc.) that may be used to force 32bit ecu to change baudrate by means of an appropriate ecu hack.

RomRaider logger may be routinely reconfiged for another baudrate here (logger.xml):
<protocol id="SSM" baud="4800" databits="8" stopbits="1" parity="0" connect_timeout="2000" send_timeout="55">

I tried this successfully for 19200, 38400bps and MicroChip 16 bit dsPIC based ecu.


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Tue Jan 26, 2010 6:47 pm 
Offline
Senior Member

Joined: Mon Jan 19, 2009 2:31 pm
Posts: 1384
Location: Saratov, Russia
I mean that I successfully communicate with my own design of 16 bits ecu build for Audi engine at 19200 and 38400 bps.

Logging is done by RR logger that is setup for 38400 communications by mean of RR "logger.xml" string <protocol id="SSM" baud="38400">


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Tue Jan 26, 2010 7:05 pm 
Offline
Experienced

Joined: Sat May 31, 2008 10:14 pm
Posts: 125
Location: Quebec
I see. I though you were able with 16bits subaru ecu.

I have my own hardware as well that speak SSM... but no luck so far with a 32 bits ecu at other speeds. I am not using RR and/or tactrix.

Mart

Sasha_A80 wrote:
I mean that I successfully communicate with my own design of 16 bits ecu build for Audi engine at 19200 and 38400 bps.

Logging is done by RR logger that is setup for 38400 communications by mean of RR "logger.xml" string <protocol id="SSM" baud="38400">


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Tue Jan 26, 2010 11:55 pm 
Offline
Newbie

Joined: Mon Oct 15, 2007 2:37 am
Posts: 18
fujiillin wrote:
Also, there's a SSM library around here somewhere in C#.


This one? http://www.codeplex.com/ssm :)

I haven't implemented writes yet, only reading (logging) because there hasn't been much use for it. However, if there's going to be an ECU hack to change the bit rate, that would certainly quality. I can provide a test utility for it as well, like a small GUI that makes it easy to select bit rates and send/receive some sample packets. Stay tuned.


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Wed Jan 27, 2010 12:31 am 
Offline
Senior Member

Joined: Mon Jan 19, 2009 2:31 pm
Posts: 1384
Location: Saratov, Russia
Mart wrote:
I see. I though you were able with 16bits subaru ecu.
I have my own hardware as well that speak SSM... but no luck so far with a 32 bits ecu at other speeds. I am not using RR and/or tactrix.


RR and modified ecuExplorer are speaking at rised baud rates with my homebrew hardware.
ANY UART or virtial COM is applicable. There is no need for Tactrix that is not opensource currently.


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Wed Jun 30, 2010 10:33 am 
Offline
Experienced

Joined: Sat May 31, 2008 10:14 pm
Posts: 125
Location: Quebec
I now have a 32 bits 06 sti in my hand. I will setup a jig and see what I can do. Using an SSM command to change the baud seem to be a good idea.


Mart wrote:
well 19200 (if working well) is better than 4800 ;)

now I need to put my hand on a 32 bits ecu and make something happen.

Sasha_A80 wrote:
It depends on the circuitry at ecu and cable sides.
Cheap optocoupled cables are limited by 19200-38400, more elaborated and DC coupled are capable to operate at higher rates.


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Fri Jun 19, 2015 3:01 pm 
Offline
Newbie

Joined: Sun Dec 01, 2013 4:17 pm
Posts: 36
Why is this dead? The sample rate at 4800 is terrible...


Top
 Profile  
 
 Post subject: Re: Baud rate for logger found for 32bit DBW
PostPosted: Fri Jun 19, 2015 3:44 pm 
Offline
RomRaider Developer

Joined: Wed May 20, 2009 9:49 pm
Posts: 5698
Location: Canada eh!
Use fast poll mode or CAN if your ROM supports it.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 69 posts ]  Go to page Previous  1, 2, 3, 4, 5

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style based on FI Subsilver by phpBBservice.nl