gabedude banned at NASIOC

gabedude · **Posted:** Mon Mar 24, 2008 1:22 am

More pics of my work.

Everything is on order now. ~3 more weeks and she will be in breakin period.

gabedude · **Posted:** Mon Mar 24, 2008 2:29 am

Oh I got flow report back on the stock injectors. #3 was the lowest flowing injector. Surprise! !not

Quote:

Gabe,

Got your cores in and had a chance to test them. Attached is the testing results. The #3 injector, same one that you marked as suspect, did flow slightly less but nothing that under normal conditions would cause any problems. It is not listed on the testing sheet, but also tested them at a couple different IDC’s and all appeared normal. In our opinion the injectors would not have caused any problems

Let me know if you have any questions

Thanks

Mike Deatsch

Obviously I was pushing the limits, but yeah #3 killed it with that bubble and running lean too much (because of the injector).

Quote:

Customer Name Sean Widmer Air Temp 75
Testing Date 03/19/08 Device New Age NA8
Make/Model Subaru Specific Gravity 0.696@25C
Injector Model Denso Testing Pressure 43.5
Injector Type top feed Calibration. Factor 1.000
Technician ID md
cc/min lbs/hr
1 567 54.0 pass pass 12.1 pass pass 6.2
2 566 53.9 pass pass 12.1 pass pass 6.2
3 555 52.9 pass pass 12.1 pass pass 6.2
4 568 54.1 pass pass 12.1 pass pass 6.2

Nuke209 · **Joined:** Sun Oct 15, 2006 9:10 pm **Posts:** 116

Quote:

Customer Name Sean Widmer Air Temp 75
Testing Date 03/19/08 Device New Age NA8
Make/Model Subaru Specific Gravity 0.696@25C
Injector Model Denso Testing Pressure 43.5
Injector Type top feed Calibration. Factor 1.000
Technician ID md
cc/min lbs/hr
1 567 54.0 pass pass 12.1 pass pass 6.2
2 566 53.9 pass pass 12.1 pass pass 6.2
3 555 52.9 pass pass 12.1 pass pass 6.2
4 568 54.1 pass pass 12.1 pass pass 6.2

EEEK!

gabedude · **Posted:** Tue Mar 25, 2008 9:41 am

Nuke209 wrote:

Quote:

Customer Name Sean Widmer Air Temp 75
Testing Date 03/19/08 Device New Age NA8
Make/Model Subaru Specific Gravity 0.696@25C
Injector Model Denso Testing Pressure 43.5
Injector Type top feed Calibration. Factor 1.000
Technician ID md
cc/min lbs/hr
1 567 54.0 pass pass 12.1 pass pass 6.2
2 566 53.9 pass pass 12.1 pass pass 6.2
3 555 52.9 pass pass 12.1 pass pass 6.2
4 568 54.1 pass pass 12.1 pass pass 6.2

EEEK!

Still within manufacturing specs though. You can imagine what it does when you are right at the limit of AFR's and timing like I was pushing it. The lowest fuel flowing cylinder went. :/

2.5LSUBWRX · **Joined:** Tue Jul 11, 2006 8:53 pm **Posts:** 48

hey was too lazy to read the whoel thing but did i see someone was looking for an 08 sti rom to mess with? right now at my work we got 2 on the lot and a gray one with very bad paint dmg in back(subaru and there paint damnit). so i prolly could pull a map off one if u need it. Jus let me know. lol u catch me within next 3hrs prolly get it today. we r slow and i am jus messing around on the internet now.

2.5LSUBWRX · **Joined:** Tue Jul 11, 2006 8:53 pm **Posts:** 48

gabedude wrote:

Ok dumb question. Is there any alternative to Fuji bond or Dow Cornng's 7038 for the gasket maker? Should I just order the Fuji Bond? I know that permatex or someone other than Dow has to make block sealant that I can just pick up at an auto parts store.

I have all the $$$ to rebuild it now. Ordering pistons and gaskets today.

also if not too late fuji bond is junk dont mess with it. Ive always just used permatex never once had a problem. the fuji stuff doesnt like too dry real well accutally when there was a recall on the parking prawls they sent fuji bond to do the recall. and i must say everyone of those cars it seem that comes back in for whatever is leaking jus a little bit from the trany pan so if it were me use p[ermatex

Exodus751 · **Posted:** Thu Mar 27, 2008 9:55 pm

are we looking for a silicon ? like a sealer ??

2.5LSUBWRX wrote:

gabedude wrote:

Ok dumb question. Is there any alternative to Fuji bond or Dow Cornng's 7038 for the gasket maker? Should I just order the Fuji Bond? I know that permatex or someone other than Dow has to make block sealant that I can just pick up at an auto parts store.

I have all the $$$ to rebuild it now. Ordering pistons and gaskets today.

also if not too late fuji bond is junk dont mess with it. Ive always just used permatex never once had a problem. the fuji stuff doesnt like too dry real well accutally when there was a recall on the parking prawls they sent fuji bond to do the recall. and i must say everyone of those cars it seem that comes back in for whatever is leaking jus a little bit from the trany pan so if it were me use p[ermatex

2.5LSUBWRX · **Joined:** Tue Jul 11, 2006 8:53 pm **Posts:** 48

Exodus751 wrote:

are we looking for a silicon ? like a sealer ??

2.5LSUBWRX wrote:

gabedude wrote:

Ok dumb question. Is there any alternative to Fuji bond or Dow Cornng's 7038 for the gasket maker? Should I just order the Fuji Bond? I know that permatex or someone other than Dow has to make block sealant that I can just pick up at an auto parts store.

I have all the $$$ to rebuild it now. Ordering pistons and gaskets today.

also if not too late fuji bond is junk dont mess with it. Ive always just used permatex never once had a problem. the fuji stuff doesnt like too dry real well accutally when there was a recall on the parking prawls they sent fuji bond to do the recall. and i must say everyone of those cars it seem that comes back in for whatever is leaking jus a little bit from the trany pan so if it were me use p[ermatex

fuji bond is a silicone. permatex's gray silicone is jus much better and availible at any auto store

Over Actor · **Posted:** Sat Mar 29, 2008 10:24 am

Not to get to off topic but since you guys are discussing Fuji bond, I like the Honda Bond alot better its pretty much the same thing but Thicker and doesnt dry out and flake off.

gabedude · **Posted:** Sun Mar 30, 2008 1:14 am

Fujibond will be here tuesday.
Gasket set and pistons will be here tuesday.
Hoses and clamps will arrive before friday.
Rebuild has started.

Pics:

I ported the 2nd TGV so much better, I had to touch up the first:

Intake manifold started assembly. Samco hoses all around (except ancillary - the stock MAF hose is being replaced):

gabedude · **Posted:** Sun Mar 30, 2008 1:18 am

2.5LSUBWRX wrote:

gabedude wrote:

Ok dumb question. Is there any alternative to Fuji bond or Dow Cornng's 7038 for the gasket maker? Should I just order the Fuji Bond? I know that permatex or someone other than Dow has to make block sealant that I can just pick up at an auto parts store.

I have all the $$$ to rebuild it now. Ordering pistons and gaskets today.

also if not too late fuji bond is junk dont mess with it. Ive always just used permatex never once had a problem. the fuji stuff doesnt like too dry real well accutally when there was a recall on the parking prawls they sent fuji bond to do the recall. and i must say everyone of those cars it seem that comes back in for whatever is leaking jus a little bit from the trany pan so if it were me use p[ermatex

To reseal the block?

The service manual calls for Three Bond 1217B for the Auto tranny pan. It only calls for Three Bond 1215B (a different sealant) on the 6MT Tranny and the block.

gabedude · **Posted:** Sun Mar 30, 2008 1:25 am

I bet this s*** would seal it. But I dunno if it would ever come apart again. hehe.

http://www.permatex.com/products/Automo ... _Stick.htm

This is even better:

http://www.permatex.com/products/Automo ... ealant.htm

This is what you are talking about right?

http://www.permatex.com/products/Automo ... ealant.htm

Turbo_Mike · **Posted:** Sun Mar 30, 2008 1:25 pm

gabedude wrote:

This is what you are talking about right?

http://www.permatex.com/products/Automo ... ealant.htm

Thats what I use. Built 2 motors this weekend :-)

Working on a closed deck JDM 2.0 now.

gabedude · **Posted:** Sun Mar 30, 2008 2:16 pm

Turbo_Mike wrote:

gabedude wrote:

This is what you are talking about right?

http://www.permatex.com/products/Automo ... ealant.htm

Thats what I use. Built 2 motors this weekend :-)

Working on a closed deck JDM 2.0 now.

Ah well s***. I guess I will just ebay the Fuji Bond.

Thanks!

bokchoi · **Joined:** Thu Nov 08, 2007 12:21 am **Posts:** 3

gabedude wrote:

This is what you are talking about right?

http://www.permatex.com/products/Automo ... ealant.htm

that stuff works great, used it for my vans transmission pan and it sealed up great, no leaks whatsoever (even with two missing bolts).

RomRaider

Forum rules

gabedude banned at NASIOC

Who is online